烟用爆珠干燥前处理工艺的研究

朱贝贝; 蔡持; 耿宗泽; 费翔; 罗诚; 杨本刚; 尹嵩; 李东亮

doi:10.12187/2020.03.007

CN 41-1437/TS ISSN 2096-1553

烟用爆珠干燥前处理工艺的研究

朱贝贝 , 蔡持 , 耿宗泽 , 费翔 , 罗诚 , 杨本刚 , 尹嵩 , 李东亮

朱贝贝, 蔡持, 耿宗泽, 等. 烟用爆珠干燥前处理工艺的研究[J]. 轻工学报, 2020, 35(3): 52-59. doi: 10.12187/2020.03.007

引用本文: 朱贝贝, 蔡持, 耿宗泽, 等. 烟用爆珠干燥前处理工艺的研究[J]. 轻工学报, 2020, 35(3): 52-59. doi: 10.12187/2020.03.007

ZHU Beibei, CAI Chi, GENG Zongze, et al. Study on pre-drying treatment technology of breakable capsules in cigarette[J]. Journal of Light Industry, 2020, 35(3): 52-59. doi: 10.12187/2020.03.007

Citation: ZHU Beibei, CAI Chi, GENG Zongze, et al. Study on pre-drying treatment technology of breakable capsules in cigarette[J]. Journal of Light Industry, 2020, 35(3): 52-59. doi: 10.12187/2020.03.007

烟用爆珠干燥前处理工艺的研究

1. 四川中烟工业有限责任公司技术中心, 四川成都 610066;
2. 四川三联新材料有限公司, 四川成都 610000

作者简介: 朱贝贝(1991-),女,河南省商丘市人,四川中烟工业有限责任公司助理工程师,主要研究方向为烟草化学、烟用材料.;

基金项目: 成都市科技项目（2018-YF05-00344-GX）
中图分类号: TS49

Study on pre-drying treatment technology of breakable capsules in cigarette

1. Technology Center, China Tobacco Sichuan Industrial Co., Ltd., Chengdu 610066, China;
2. Sichuan Sanlian New Materials Co., Ltd., Chengdu 610000, China
Received Date: 2019-12-27

CLC number: TS49

摘要: 采用水清洗、乙醇清洗、钙化处理后水清洗、钙化处理后乙醇清洗4种工艺分别对爆珠进行干燥前处理，从中筛选出适宜的前处理工艺，在此基础上分析钙化浓度对爆珠粒径和压碎强度的影响，确定爆珠干燥前钙化处理中的钙化浓度.结果表明：钙化处理后水清洗为适宜的爆珠干燥前处理工艺，0.3%为适宜的钙化浓度.采用该爆珠干燥前处理工艺和钙化浓度，可以缩短湿爆珠干燥时间、减少能耗，提高生产效率和成品爆珠产品质量的一致性.
- 烟用爆珠 /
- 干燥前处理 /
- 钙化 /
- 爆珠粒径 /
- 爆珠压碎强度
Abstract: Four kinds of pre-drying treatment technology:water cleaning,ethanol cleaning,water cleaning after calcification treatment and ethanol cleaning after calcification treatment,were used to dry the breakable capsule and select the appropriate pre-drying treatment technology.The influence of calcification concentration on the particle size and crushing strength of the breakable capsule was analyzed,and the calcification concentration in the process of calcification before the breakable capsule drying was determined.The results showed that the water cleaning after calcification treatment was the appropriate pre-drying treatment technology for breakable capsule,and 0.3% was the appropriate calcification concentration.The use of the pre-drying treatment technology and calcification concentration could shorten the drying time of wet breakable capsule,reduce energy consumption,and improve the production efficiency and the consistency of finished breakable capsule products.
- breakable capsule in cigarette /
- pre-drying treatment /
- calcification /
- particle size of breakable capsule /
- crushing strength of breakable capsule
1. [1]
  洪广峰,邱纪青,李国政,等.国外爆珠卷烟研究进展[J].中国烟草学报,2019,25(4):124.
2. [2]
  崔春,孟祥士,纪朋,等.陈皮爆珠对卷烟常规理化指标和感官品质的影响[J].轻工学报,2019,34(5):40.
3. [3]
  何媛,彭军仓,吕娟,等.GC/MS指纹图谱及系统聚类分析用于烟用爆珠内含物的测定[J].烟草科技,2018,51(7):54.
4. [4]
  席辉,柴国璧,张启东,等.卷烟爆珠溶剂中链甘油三酯的分离与鉴定[J].烟草科技,2018,51(7):61.
5. [5]
  刘秀明,张健,刘亚,等.高效液相色谱法同时测定爆珠壁材中8种水溶性着色剂[J].中国测试,2018,44(3):48.
6. [6]
  朱风鹏,李雪,罗彦波,等.爆珠破碎对主流烟气有害成分释放量和滤嘴截留的影响[J].烟草科技,2017,50(4):37.
7. [7]
  朱瑞芝,詹建波,蒋薇,等.GC-MS/MS法分析爆珠关键成分在卷烟中的转移行为[J].烟草科技,2018,51(6):58.
8. [8]
  XIE Z P,WANG X,JIA Y,et al.Ceramic forming based on gelation principle and process of sodium alginate[J].Materials Letters,2003,57(9):1635.
9. [9]
  张东.褐藻胶植物肠溶空心硬胶囊制备技术[D].青岛:中国海洋大学,2010.
10. [10]
  郭庆.毫米级海藻酸钙基大胶囊的可控制备、囊壁改性及其性能[D].武汉:武汉纺织大学,2018.
11. [11]
  王康,何志敏.海藻酸钠与钙或锌离子凝胶动力学过程研究[J].离子交换与吸附,2004(5):424.
12. [12]
  许加超,卢伟丽,高昕,等.氯化钙体系制备的褐藻酸钙凝胶特性的研究[J].渔业科学进展,2010,31(1):100.
13. [13]
  KLEMM W R.Dehydration: A new alcohol theory[J].Alcohol,1990,7(1):49.
14. [14]
  张青,许加超,付晓婷,等.钙化条件对海藻酸钙空心硬胶囊成型性的影响[J].中国海洋药物,2012(5):11.
15. [15]
  PATHAK T S,YUN J H,LEE J,et al.Effect of calcium ion (cross-linker) concentration on porosity,surface morphology and thermal behavior of calcium alginates prepared from algae (Undaria pinnatifida)[J].Carbohydrate Polymers,2010,81(3):633.
1. [1]
  贾尚羲 , 张怡雪 , 石盼盼 , 王昱 , 李可 . 不同时长超声波处理对鹰嘴豆分离蛋白乳化液稳定性的影响. 轻工学报, 2024, 39(5): 40-49. doi: 10.12187/2024.05.005
2. [2]
  卢晓波 , 徐海 , 朱俊召 , 张宇 , 谭健 , 高冠男 , 胡军华 , 林龙 . 基于机器视觉的加热卷烟烟支端部质量检测系统设计. 轻工学报, 2024, 0(0): -.

点击查看大图

计量

PDF下载量: 34
文章访问数: 2732
引证文献数: 0

通讯作者: 陈斌, bchen63@163.com

1.
沈阳化工大学材料科学与工程学院沈阳 110142

朱贝贝, 蔡持, 耿宗泽, 等. 烟用爆珠干燥前处理工艺的研究[J]. 轻工学报, 2020, 35(3): 52-59. doi: 10.12187/2020.03.007

引用本文: 朱贝贝, 蔡持, 耿宗泽, 等. 烟用爆珠干燥前处理工艺的研究[J]. 轻工学报, 2020, 35(3): 52-59. doi: 10.12187/2020.03.007

ZHU Beibei, CAI Chi, GENG Zongze, et al. Study on pre-drying treatment technology of breakable capsules in cigarette[J]. Journal of Light Industry, 2020, 35(3): 52-59. doi: 10.12187/2020.03.007

烟用爆珠干燥前处理工艺的研究

作者简介:朱贝贝(1991-),女,河南省商丘市人,四川中烟工业有限责任公司助理工程师,主要研究方向为烟草化学、烟用材料.

1. 四川中烟工业有限责任公司技术中心, 四川成都 610066;
2. 四川三联新材料有限公司, 四川成都 610000

收稿日期: 2019-12-27

基金项目: 成都市科技项目（2018-YF05-00344-GX）

关键词:

摘要: 采用水清洗、乙醇清洗、钙化处理后水清洗、钙化处理后乙醇清洗4种工艺分别对爆珠进行干燥前处理，从中筛选出适宜的前处理工艺，在此基础上分析钙化浓度对爆珠粒径和压碎强度的影响，确定爆珠干燥前钙化处理中的钙化浓度.结果表明：钙化处理后水清洗为适宜的爆珠干燥前处理工艺，0.3%为适宜的钙化浓度.采用该爆珠干燥前处理工艺和钙化浓度，可以缩短湿爆珠干燥时间、减少能耗，提高生产效率和成品爆珠产品质量的一致性.

English Abstract

Study on pre-drying treatment technology of breakable capsules in cigarette

1. Technology Center, China Tobacco Sichuan Industrial Co., Ltd., Chengdu 610066, China;
2. Sichuan Sanlian New Materials Co., Ltd., Chengdu 610000, China

Received Date: 2019-12-27

Abstract: Four kinds of pre-drying treatment technology:water cleaning,ethanol cleaning,water cleaning after calcification treatment and ethanol cleaning after calcification treatment,were used to dry the breakable capsule and select the appropriate pre-drying treatment technology.The influence of calcification concentration on the particle size and crushing strength of the breakable capsule was analyzed,and the calcification concentration in the process of calcification before the breakable capsule drying was determined.The results showed that the water cleaning after calcification treatment was the appropriate pre-drying treatment technology for breakable capsule,and 0.3% was the appropriate calcification concentration.The use of the pre-drying treatment technology and calcification concentration could shorten the drying time of wet breakable capsule,reduce energy consumption,and improve the production efficiency and the consistency of finished breakable capsule products.

参考文献 (15) 相关文章 (2)