角窗塑件注射压缩成型工艺数值模拟研究

张果; 郭会师; 蒋晶; 李倩

doi:10.12187/2020.03.010

May 2020

Article Contents

ZHANG Guo, GUO Huishi, JIANG Jing and et al. Numerical simulation research on injection-compression molding process of corner window plastic parts[J]. Journal of Light Industry, 2020, 35(3): 82-87. doi: 10.12187/2020.03.010

Citation: ZHANG Guo, GUO Huishi, JIANG Jing and et al. Numerical simulation research on injection-compression molding process of corner window plastic parts[J]. Journal of Light Industry, 2020, 35(3): 82-87. doi: 10.12187/2020.03.010 shu

Numerical simulation research on injection-compression molding process of corner window plastic parts

ZHANG Guo ¹ ,
GUO Huishi ¹ ,
JIANG Jing ² ,
LI Qian ²

1. College of Material and Chemical Engineering, Zhengzhou University of Light Industry, Zhengzhou 450001, China;
2. National Center for International Joint Research of Micro-Nano Moulding Technology, Zhengzhou University, Zhengzhou 450001, China

Received Date: 2019-12-17

Abstract

Through numerical simulation method which combined Moldflow software with orthogonal experiment,the residual stress distribution after demoulding in the thickness direction of three typical positions of polycarbonate corner window plastic parts was studied, and the injection compression molding process of corner window plastic parts was optimized. On the basis, the main factors were selected to investigate the influence of the main process parameters on the residual stress of the product.The results showed that the residual stress distribution after demoulding in the thickness direction of three typical locations of the product conforms to the three-region distribution of tension-compression-tension.The optimum combination of process parameters was that the mold temperature was 105 ℃, the melt temperature was 315 ℃, the injection time was 3 s, the compression force was 882 kN, the compression distance was 1.0 mm, the compression speed was 5 mm/s, and the delay time was 0 s.Melt temperature, delay time, compression distance were the main process parameters that affect the residual stress of the product, and the residual stress of the subsurface layer and the center layer of the plastic part decreased with the increase of the melt temperature, while the residual stress of each layer in the thickness direction of the plastic part increased with delay time and compression distance.
- injection-compression molding,
- residual stress,
- orthogonal experiment,
- numerical simulation
References
1. [1]
  肖九梅.浅述塑料注射压缩成型技术及应用[J].塑料包装,2018,28(5):54.
2. [2]
  安紫娟,何继敏,王国俨,等.注射压缩模具及注射压缩成型技术研究进展[J].现代塑料加工应用,2019,31(6):60.
3. [3]
  杜遥雪,史智,周阳,等.注射压缩成型LED透镜光学性能分析[J].中国塑料,2018,32(5):103.
4. [4]
  YOUNG I K,YOUNG S S.Application of injection compression molding to thin-walled polymeric parts[J].Korea-Australia Rheology Journal,2018,30(3):161.
5. [5]
  李小林,洪剑城.Moldflow在注射压缩成型中的应用[J].工程塑料应用,2012,40(3):49.
6. [6]
  KABANEMI K,VAILLANCOURT H,WANG H,et al.Residual stresses,shrinkage,and warpage of complex injection molded products:Numerical simulation and experimental validation[J].Polym Eng Sci,2004,38(1):21.
7. [7]
  HWA J O,YOUNG S S.Enhanced impact strength of injection-compression molded parts by controlling residual stress distribution[J].Korea-Australia Rheology Journal,2019,31(1):35.
8. [8]
  沈红雷,袁毅,薛露.注射压缩工艺参数对厚壁塑件成型质量的影响[J].机床与液压,2018,46(4):9.
9. [9]
  OLIAEI E,HEIDARI B S,DAVACHI S M,et al.Warpage and shrinkage optimization of injection-molded plastic spoon parts for biodegradable polymers using Taguchi,ANOVA and artificial neural network methods[J].Journal of Materials Science & Technology,2016,32(8):710.
10. [10]
  韩健,李刚,陈静波,等.注塑件残余应力影响因素的模拟实验研究[J].塑料工业,2007(2):23.
Proportional views

Get Citation

PDF

XML

Article Metrics

Article views(1535) PDF downloads(10) Cited by()

Ralated

通讯作者: 陈斌, bchen63@163.com

1.
沈阳化工大学材料科学与工程学院沈阳 110142

Numerical simulation research on injection-compression molding process of corner window plastic parts

Abstract

References

Proportional views

Article Metrics

Ralated

Proportional views

通讯作者: 陈斌, bchen63@163.com