原位反应剂质量分数对复合强化法制备混杂颗粒增强铝基复合材料的影响
Effect of in-situ reactant mass fraction on hybrid particle reinforced aluminum matrix composites prepared by composite strengthening method
-
摘要: 采用纳米颗粒强化、热压强化等多种方式相结合的复合强化法，以Al-Si系合金为基体、纳米级CuO颗粒为原位反应剂，外加微米SiC颗粒制备多尺度混杂颗粒增强铝基复合材料，并对其组织形貌进行表征，研究CuO质量分数对其硬度和耐磨性的影响.结果表明：所得复合材料的组织为共晶组织（α+Si）+SiC颗粒+AlCu3颗粒，且随着CuO质量分数的增加，共晶组织的α晶粒和点状Si变得更加细小.当CuO质量分数为3.0%，即试样配方为3.0% CuO+15.0% SiC+82.0% Al-Si时，复合材料的硬度最大，为88.8 HB，比基体硬度（51.8 HB）提高了71.4%；同时，复合材料的磨损量最低，为0.003 0 g，且耐磨性最好，相对耐磨性为2.93%，是基体耐磨性的2.93倍.
-
关键词:
- 原位反应剂 /
- 复合强化法 /
- 混杂颗粒增强铝基复合材料 /
- 耐磨性
Abstract: The reinforced aluminum matrix composites was prepared by using the composite strengthening method combining various methods such as nanoparticle strengthening and hot pressing strengthening, with Al-Si alloy as the matrix, nano-scale CuO particles as the in-situ reactant, and micron SiC particles plus multi-scale hybrid particles, the structure and morphology of the composites were characterized, and the effect of the in-situ reactant CuO mass fraction on its hardness and wear resistance was studied. The results showed that the structure of the obtained composites was eutectic structure (α + Si) + SiC particles + AlCu3 particles, and with the increase of the mass fraction of CuO, the α grains and point Si of the eutectic structure became finer. When the CuO mass fraction was 3.0%, that was, the sample formula was 3.0% CuO+15.0% SiC+82.0% Al-Si, the composites had the largest hardness of 88.8 HB, which was 71.4% higher than the matrix hardness (51.8 HB). At the same time, the composites had the lowest wear amount of 0.003 0 g, and the best wear resistance, the relative wear resistance was 2.93%, which was 2.93 times that of the matrix. -
-
[1]
吴树森,高琦,杜睿,等.单相或混杂颗粒增强铝基复合材料的原位制备技术[J].西华大学学报(自然科学版),2018(4):1.
-
[2]
HIRSCH J.Recent development in aluminium for automotive applications[J].Transactions of Nonferrous Metals Society of China,2014,24(7):1995.
-
[3]
席小鹏,王快社,王文,等.搅拌摩擦加工制备颗粒增强铝基复合材料的研究现状及展望[J].材料导报,2018,32(21):140.
-
[4]
纪兴华,吕昕晖,陈刚,等.粉末冶金及热挤压制备SiCP/铝基复合材料的磨损性能[J].特种铸造及有色合金,2019,39(1):67.
-
[5]
HANABE M R,ASWATH P B.Al2O3/Al particle-reinforced aluminum matrix composite by displacement reaction[J].Journal of Materials Research,1996,11(6):1562.
-
[6]
屈敏,刘鑫,崔岩,等.TiB2颗粒尺寸和质量分数对原位自生TiB2/Al复合材料耐磨性能的影响[J].铸造,2018(5):404.
-
[7]
SINGH J,CHAUHAN A.Characterization of hybrid aluminum matrix composites for advanced applications:A review[J].Journal of Materials Research & Technology,2016,5(2):159.
-
[8]
高红霞,王蒙,樊江磊,等.混杂颗粒增强铝基复合材料的研究进展[J].粉末冶金工业,2019,9(3):1.
-
[9]
杨绍斌,张旭,谢帅.高质量分数Al2O3/Al复合材料的硬度和耐磨性能[J].材料保护,2018,51(4):47.
-
[10]
BHARATH V,AJAWN S S,NAGARAL M,et al.Characterization and mechanical properties of 2014 aluminum alloy reinforced with Al2O3P composite produced by two-stage stir casting route[J].J Inst Eng India Ser C,2019,100(2):277.
-
[11]
邓德杰,赵海东,李芳东.挤压铸造10SiCP/A356铝基复合材料的摩擦磨损性能[J].特种铸造及有色合金,2018,38(12):1327.
-
[12]
秦蜀懿,张国定.改善颗粒增强金属基复合材料塑性和韧性的途径与机制[J].中国有色金属学报,2000(5):621.
-
[1]
-
点击查看大图
计量
- PDF下载量: 9
- 文章访问数: 1962
- 引证文献数: 0
下载:
